元器件交易网www.cecb2b.com
Slotted Optical Switch
OPB806
Features: • Non-contact switching • Base or side mounting • 0.125” (3.175 mm) slot width • 0.500” (12.700 mm) lead spacing Product Photo Here Description:
The OPB806 slotted optical switch consists of an infrared emitting diode (LED) and a NPN silicon phototransistor, mounted on opposite sides of a 0.125” (3.175 mm) wide slot.
The OPB806 has two sets of mounting tabs allowing Base or Side mounting of the device. The LED and phototransistor leads project from each side of the housing on 0.050” (1.27 mm) centers.
Phototransistor switching takes place whenever an opaque object passes through the slot.
Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information.
Applications:
• Non-contact interruptive object sensing • Assembly line automation • Machine automation • Equipment security • Machine safety LED Peak Part Number Wavelength
OPB806
935 nm
Sensor
Transistor
Slot Width / Depth
0.125\" / 0.375”
Aperture
None
Lead Length
0.500\"
1 3 2 4 Pin # Description 1 Anode 2 Cathode 3 Collector 4 Emitter RoHS
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A 12/05
Page 1 of 3
OPTEK Technology Inc. — 15 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
元器件交易网www.cecb2b.com
Slotted Optical Switch
OPB806
Absolute Maximum Ratings (TA=25°C unless otherwise noted)
Storage & Operating Temperature Range
-40° C to +85° C
Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] (1) 260° C Input Diode
Continuous Forward Current
Peak Forward Current (1 µs pulse width, 300 pps) Reverse Voltage Power Dissipation (2) Output Phototransistor
Collector-Emitter Voltage Emitter-Collector Voltage Power Dissipation (2)
30 V 5 V 100 mW 50 mA 3 A 2 V 100 mW
Electrical Characteristics (TA = 25°C unless otherwise noted)
SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (See OP165 for additional information)
VF Forward Voltage IR Reverse Current
- - 1.7 V IF = 20 mA - - 100 µA VR = 2 V
Output Phototransistor (See OP505 for additional information) Breakdown Voltage 30 V(BR)CEO Collector-Emitter Breakdown Voltage V(BR)ECO Emitter-Collector ICEO Combined
Saturation Voltage VCE(SAT) Collector-Emitter IC(ON)
On-State Collector Current
- 0.4
- -
0.5 -
V IC = 200 µA, IF = 20 mA mA
VCE = 0.5 V, IF = 20 mA
Collector-Emitter Dark Current
5 -
- - -
- - 100
V IC = 100 µA V IE = 100 µA nA
VCE = 10 V, IF = 0, EE = 0
Notes:
(1) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (2) Derate linearly 1.67 mW/°C above 25 ° C..
(3) Methanol or isopropanol are recommended as cleaning agents. Plastic housing is soluble in chlorinated hydrocarbons and
ketones.
(4) All parameters were tested using pulse technique.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A 12/05 Page 2 of 3
OPTEK Technology Inc. — 15 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
元器件交易网www.cecb2b.com
Slotted Optical Switch
OPB806
OPB806 - Flag Next to Emitter1.20OPB806 - Flag Next to Sensor1.201.001.000.80Typical IC(ON) Response (mA)Typical IC(ON) Response (mA)0.800.600.600.400.40Right to Left0.20Right to LeftLeft to RightTop to Bottom0.20Left to RightTop to Bottom0.000.000.050.100.150.200.000.000.050.100.150.20Displacement Distance (inches)Displacement Distance (inches)OPB806 - Flag in Middle of Slot1.20 Test Schematic 1.00Typical IC(ON) Response (mA)0.800.600.40Right to Left0.20Left to RightTop to Bottom0.000.000.050.100.150.20Displacement Distance (inches)OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 15 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A 12/05
Page 3 of 3
